Ubiquiti Networks AF-24 Guida Utente

24 GHz Point to Point 1.4+ Gbps RadioModel: AF-24

3. Connect the other end of the Ethernet cable from the DATA port to the Ethernet port labeled POE on the GigE PoE Adapter.4. Connect the Power Cord

airFiber ConfigurationThe instructions in this section explain how to access the airFiber Configuration Interface and configure the following settings

1. Connect an Ethernet cable from your computer to the CONFIG port on the airFiber AF-24.2. Configure the Ethernet adapter on your computer with a s

5. Click the Wireless tab.6. Enter the Basic Wireless Settings:a. For one airFiber AF-24, select Master from the Wireless Mode drop-down. For the o

7. Configure the Wireless Security: a. Select the AES Key Type, HEX or ASCII.b. For the Key field: - HEX Enter 16 bytes (eight, 16-bit HEX values:

Hardware InstallationTo install the airFiber AF-24:1. Insert the four Carriage Bolts into the Pole Mount Bracket.2. Attach the Pole Mount Bracket to

3. Loosen, but do NOT remove the eight Lock Bolts located on the Alignment Bracket.4. Ensure that there is a 6 mm gap between the head of each M8x14

5. Lift the airFiber AF-24 and align the four M8x14 Serrated Flange Screws with the slots on the Pole Mount Bracket. Seat the screws in the slots. Se

6. Attach a ground wire: a. Remove the nut from the Ground Bonding Point.b. Attach a ground wire (min. 8 AWG or 10 mm2) to the lug and replace the

Connecting Ethernet1. Turn the Cover Lock to the Unlocked icon. Slide the Port Cover down to remove it.2. Connect a TOUGHCable or other outdoor, s

4. Connect the other end of the Ethernet cable from the DATA port to the Ethernet port labeled POE on the GigE PoE Adapter.5. Connect an Ethernet ca

Below is a diagram of a finished installation with recommended surge protectors installed.Ground to Pole, Tower, or Grounding Block (Max. 1 m from Gr

AlignmentTips• Fine-tuning is best achieved by a pair of installers with a dedicated, two-way communication link: one installer makes adjustments on

2. For the Master and Slave, ensure the Azimuth (AZ) and Elevation (EL) Adjustment Bolts are in the middle of their adjustmentranges.Elevation (EL)

5. Master Adjust the azimuth and elevation of the Master until the strongest received signal level is displayed on the LED Display of the Master.a.

Fine-Tuning the LinkThe Azimuth (AZ) and Elevation (EL) Adjustment Bolts of the Alignment Bracket adjust the azimuth and elevation within a range of ±

There are three methods for determining the received signal level:• LED Display (described above)• airFiber Configuration Interface• Audio tone (op

SpecificationsairFiber AF-24Dimensions 649 x 426 x 303 mm (25.55 x 16.77 x 11.93")Weight 10.5 kg (23.15 lb) Mount IncludedOperating Frequency 24

Electrical Safety Information1. Compliance is required with respect to voltage, frequency, and current requirements indicated on the manufacturer’s l

Warranty ConditionsThe above warranty does not apply if the Product:(I) has been modified and/or altered, or an addition made thereto, except by Ubiq

IntroductionThank you for purchasing the Ubiquiti Networks® airFiber® 24GHz Point-to-Point Radio. This Quick Start Guide is designed to guide you thr

DisclaimerEXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA, SERVICE, SOFTWARE

NoteSome countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You

Industry CanadaCAN ICES-3(A)/NMB-3(A)This Class A digital apparatus complies with Canadian CAN ICES-3(A).To reduce potential radio interference to oth

CE MarkingCE marking on this product represents the product is in compliance with all directives that are applicable to it. This equipment is intended

PHRRJL090514Magyar [Hungarian]Alulírott, UBIQUITI NETWORKS nyilatkozom, hogy a UBIQUITI NETWORKS device, megfelel a vonatkozó alapvetõ követelményekne

© 2012-2014 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, UbiquitiNetworks, the Ubiquiti U logo, the Ubiquiti beam logo, airFiber, EdgeRoute

Hardware OverviewSideAlignment BracketElevation AdjustmentAzimuth AdjustmentGround Bonding PointLock BoltsLock Bolts2airFiber® AF-24 Quick Start Guide

BackLock BoltsLock BoltsAzimuth AdjustmentLock BoltsLock BoltsCover LockElevation AdjustmentPort Cover3Hardware Overview

InterfacesRESET DATA AUX CONFIGLED DisplayInterface DescriptionRESETTo reset to factory defaults, press and hold the Reset button for more than five s

LED State StatusDATASpeedOff 10/100 MbpsOn 1000 MbpsLink/ActOff No Ethernet LinkOn Ethernet Link EstablishedRandom Flashing Ethernet ActivityAUXGPSOff

Installation Requirements• 17 mm wrench• 13 mm socket wrench or driver• Clear line of sight between airFiber radios• Clear view of the sky for pro

• Once configuration is complete, disconnect the cables to move the airFiber radios.• Reconnect at the site. • After you have mounted the airFiber